Pertech 5300 Manuel d'utilisateur télécharger pdf (Page 28)

Pertech Resources Inc. November 2005 220321A 22

=================================

Press paper feed to change conguration

SET-UP INSTRUCTIONS

PRESSING THE PAPER FEED BUTTON WHILE THE

GREEN LIGHT IS FLASHING WILL REJECT THE

LAST PRINTED PARAMETER. IF THE BUTTON IS

NOT PRESSED WITHIN 5 SECONDS. THE PARAM-

ETER WILL BE ACCEPTED AND THE NEXT SET-UP

OPTION WILL BE LISTED.

PRESS THE PAPER FEED BUTTON NOW TO

REJECT THE CURRENT CONFIGURATION AND

CONTINUE WITH THE PRINTER SET-UP.

Printer Control Language

PCL: ACL Language

Diag: Standard Print

Auto LF: CR=CR

Font:

Font: ACL Language

Font Quality: Draft

Intl Char Set: USA

Code Page: 437 USA

Receipt LPI: 6 PLI

Validation LPI :6LPI

RS232 Serial (when used)

Baud Rate: 57.6K

Data Bits: 8 Bits

Stop Bits: 1

Parity: None

Flow Control: Hardware

Baud Rate Options:

9600

19.2K

38.4K

57.6K

Baud Rate: 57.6

Baud Rate: 9600

Stop Bit Options:

1-Bit

2-Bit

Stop Bits: 1 Bit

Parity Options:

None

Even

Odd

Parity: None

Flow Control Options:

Hardware

Software

Flow Control: Hardware

Flow Control: Software

USB (when used)

Descriptor: Model Number

Hardware

Mechanism Model:JRNL / VAL

Validation Clamp: Closed

Paper Low Stop: Disabled

Ink Status Reset: Automatic

Document Stop: 1.75 inches

Column Alignment

Half Speed: X

Full Speed: X

Tallies

Printed Lines:

Dot Count:

Validation Opens:

Feed Distance:

Hours On;

Flash Updates:

Cover Opens:

Diagnostic:

0 0 0

Conguration Report to follow

Conguration Example:

Congure the RS232 Serial parameters for the printer using the

conguration menu.

Current Param-

eters

Change to:

Baud Rate 57.6 9600

Data Bits 8 8

Stop Bits 1 1

Parity None None

Flow Control Hardware Software

Press and hold the Paper Feed Button and then press the

Power Switch to turn the printer on.

Release the Paper Feed Button after 4 seconds for the congu-

ration report to begin printing.

At the end of the conguration report the printer will prompt “

Press Paper Feed to Change Conguration” .

Press the Paper Feed Button.

The Setup instructions will print and prompt to:

“PRESS THE PAPER FEED BUTTON NOW TO REJECT

THE CURRENT CONFIGURATION AND CONTINUE WITH

THE PRINTER SET-UP”

Press the Paper Feed Button.

The First Menu Item will appear “Printer Control Language”.

Wait 5 seconds and the next Menu Item will appear “Font”. Wait

5 seconds and the “RS232 Serial (When Used)” Menu will ap-

pear.

Press the Paper Feed Button

The “Baud Rate Options” will appear

Press the Paper Feed Button

The currently selected Baud Rate “57.6K” will appear

Press the feed button until the 9600 parameter appears then

wait 5 seconds for the next option.

The “Stop Bits” parameter will appear

Wait 5 seconds and the next Menu Item will appear “Parity

Options”. Wait 5 seconds and the next Menu Item will appear

“Flow Control Options”.

Press the Paper Feed Button

The currently selected Flow Control Option, “Hardware” will

appear

Press the Paper Feed Button until the “Software” parameter

appears then wait until the printer goes through the rest of the

menus and prints off the conguration Report.

Check the New Report with the old to make sure the setting are

now correct.

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 39 40

Commentaires sur ces manuels

Pas de commentaire

Pertech 5300 Manuel d'utilisateur Page 28

Commentaires sur ces manuels

Produits connexes et manuels pour Imprimeurs Pertech 5300